Compound die

美 [ˈkɑːmpaʊnd daɪ]英 [ˈkɒmpaʊnd daɪ]
  • 网络复合模具;复合冲模
Compound dieCompound die
  1. Design of the Automatic Compound Die for the Computer Case

    电脑机箱自动复合模设计

  2. Design of Drawing and Extruding Compound Die for Step Parts

    阶梯件拉伸挤压复合模设计

  3. The compound die structure and working principle were introduced .

    介绍了落料-拉延-翻边复合模的模具结构及其工作原理。

  4. Processing Method of Compound Die with Hard Alloy for Silicon Steel Piece

    硅钢片硬质合金复合冲模工作零件加工方法

  5. Research on heat treatment process of 65 Nb steel compound die for manufacturing

    采用65Nb钢的C(63)侧架磨耗板复合冲模热处理工艺研究

  6. Design and Manufacture of the Shared Plate for the Compound Die

    复合模共用模板的设计与加工

  7. Design of the Compound Die with Two - stage Floating Elastic Pressing

    二级浮动弹压复合模设计

  8. Technological Analysis and Design of Compound Die for Diesel Engine Machine Oil Scale Frame

    柴油机机油标尺座冲压工艺分析与复合模设计

  9. The structure design of compound die of six procedures is introduced in detail .

    对6个工序的复合冲裁模具在结构设计方面作了比较详细的介绍。

  10. Development and ve search for compound die forging of gear

    齿轮复合模锻的开发与研制

  11. The designing application of compound die of external friction pieces

    外摩擦片复合冲模的设计应用

  12. Design of the Compound Die for Small Bent Parts

    小型弯曲件复合模设计

  13. Compound Die Casting Technique for Vacuum Pump Body

    真空泵泵体外壳复合金属型铸造工艺

  14. Design of Piercing and Blending Compound Die for the Blade Box

    刀片盒冲孔弯曲复合模设计

  15. Design of Forming Piercing Compound Die and Improvement for the Leaking Plate

    漏盘成形冲孔复合模设计及改进

  16. Design of Drawing and Piercing Compound Die with Floating Punch Block

    带有浮动凸凹模的拉伸冲孔复合模设计

  17. New Type Compound Die for Blanking and Drawing with Constant Blank Holder Pressure

    新型恒压边力落料拉伸复合模

  18. The design describes the structure of compound die stamping flip-chip design and working process .

    本次设计阐述了冲压倒装复合模的结构设计以及工作过程。

  19. Compound die design for signal receiver

    电子信号接收器复合模具设计

  20. Design of compound die of fine stamping eccentric brake ring

    偏心制动圈精冲复合模设计

  21. The CAD Design of Compound Die for Blanking and Drawing Based on SolidWorks

    基于SolidWorks的落料拉深复合模CAD设计

  22. The Compound Die Design

    复合冲裁模设计

  23. Design of Compound Die for the Muffler Plate

    消声器后盖复合模设计

  24. A Compound Die for Multiple Parts with No Scraps

    一模多件无废料复合模

  25. Design of Baffle Compound Die Complex Numbers

    隔板复合模设计

  26. In addition , both the working process of compound die and questions required attention are stated .

    同时也阐述了复合模工作过程及注意事项。

  27. Design of Drawing and Piercing Compound Die

    拉伸冲孔复合模设计

  28. The Flexible Compound Die for Stamping and Forming The Design for Stamping Die of Composite Structure

    柔性冲压成形复合模镶拼式冲模设计

  29. The Flexible Compound Die for Stamping and Forming

    柔性冲压成形复合模复动轮拉杆式抽油机

  30. Elastic Unloading Settings Preventing Working Parts From Inserting Waster in Compound Die

    复合模中防止工件嵌入废料的弹性卸料装置